sugar processing production line

Product Name: sugar processing production line

Specifications

1.Air classifier product size d97: 2 ~150micron,adjustable; 2.Low rotation speed; 3.Low wear.

Working Principle

Air classifier works with cyclone separator, dust collector and suction fan to form a complete classifying system. Material would go from the bottom part of air classifier up to the classifying chamber by the air flow from suction fan. The highspeed rotation of classifier wheel would create a strong centrifugal force to separate coarse powder and fine powder. Qualified fine powder would go through the wheel vane then into the cyclone separator or dust collector, while mixture of coarse powder and fine powder would lose its speed and fall down along the house wall to the secondary air inlet. The secondary air flow would disperse it further and separate coarse and fine powder. Fine powder would go up to the classifying chamber for further classifying, while coarse powder would fall down and go out from the bottom outlet.

Performance Features

• Suitable for dry fine powder classifying, powders of ball shape, flake shape and needle shape, also powders with different densities.

• Product size from classifier can vary from d97: 2micron to 150micron. The product size is adjustable, which makes the change of product size easy and simple.

• Classifying efficiency (extraction rate) can be between 60% and 90%. Material with good flowability would have high classifying efficiency, otherwise, the classifying efficiency would be low.

• Vertical type of classifier wheel would have low rotation speed, low wear and low motor power.

• Several units of classifiers can be connected in series to produce several different sizes.

• It can be connected with ball mill, vibration mill or Raymond mill to form a close-loop recycling system.

• Control system has program control, can indicate real-time status, which make operate very convenient.

•Negativepressure system. Dust emission would be less than 40mg/m3. Our machines have noise isolation device, which makes noise not higher than 75dB(A).

Technical Parameters

Note: throughput depends on heavily raw material size, density, moisture and flow-ability. The data above is just for your reference.

Manufacture Workshop &Testing Workshop

Our Honour

Customer Visiting

When is operating, prepared materials enter the extruding chamber from the hopper and then moves forwards by the rotating pressing.sugar processing production line Screwed and is pressed. Under the high pressure will be created, which also creates friction and relative movement among material particles. On the other hand,sugar processing production line root diameter of the pressing screw varies larger from one end to the other hence, when rotating, it not only pushes particles moving but turns outwards as well.

Meanwhile sugar processing production line particles adjacent the screw will rotate along with screw's rotating, causing every particle adjacent the screw will rotate along with screw's rotating, causing every particles insides the chamber to posses different speed. Therefore, relative movement among particles creates heat which is necessary during manufacturing because of helping protein change properly, damage cold oil ,decrease plasticity, decrease oil, elasticity, resulting in high oil productivity.

sugar processing production line Conventional coconut oil processors use hexane as a solvent to extract up to 10% more oil than produced with just rotary mills and expellers. They then refine the oil to remove certain free fatty acids to reduce susceptibility to rancidification. Other processes to increase shelf life include using copra with a moisture content below 6%, keeping the moisture content of the oil below 0.2%, heating the oil to 130-150 °C (266-302 °F) and adding salt or citric acid.
Virgin coconut oil (VCO) can be produced from fresh coconut milk, meat, or residue. Producing it from the fresh meat involves either wet-milling or drying the residue, and using a screw press to extract the oil. VCO can also be extracted from fresh meat by grating and drying it to a moisture content of 10-12%, then using a manual press to extract the oil. Producing it from coconut milk involves grating the coconut and mixing it with water, then squeezing out the oil. The milk can also be fermented for 36-48 hours, the oil removed, and the cream heated to remove any remaining oil. A third option involves using a centrifuge to separate the oil from the other liquids. Coconut oil can also be extracted from the dry residue left over from the production of coconut milk.
Jinan Joysun Machinery Co., Ltd. provide hydraulic oil expeller and scew oil press machine to extract the coconut oil forits customers. Big production capacity, automatic lifting, pressing and filtering are features of screw oil press machine, also a coconut oil production line is available too. Contatc us for detail.