plant cpo refinery processing

plant cpo refinery processing

plant cpo refinery processing

1, plant cpo refinery processing introduction

What kind of palm oil refinery plant we can supply ?

1. Batch type palm oil refinery plant: 1-30tons per 24hrs.

2. Semi-continuous type crude oil refinery: 20-50tons per 24hrs.

3. Continuous type crude oil refinery: 30-600tons per 24hrs.

What kind of crude vegetable oil can be refine?

Crude soybean oil, palm oil, palm kernel oil, sunflower oil, canola oil(rapeseed oil) ,peanut oil,

sesame oil, conttonseeds oil etc.

2, plant cpo refinery processing main procedures

Hydration Deguming & Alkali Refining Deacidification

The crude oil is output by the oil feed pump from the oil tank, and next enters the crude oil heat

exchanger to recover part of heat after metering and then is heated to the required temperature

by the heater. After that, the oil is mixed with the metered phosphoric acid or citric acid from

phosphate tank in the gas mixture (M401), and then enters the conditioning tank (R401) to make

the non-hydratable phospholipids in oil change into the hydratable phospholipids.

Add the alkali for neutralization, and the alkali quantity and alkali solution concentration depend

on the quality of the crude oil. Through the heater, the neutralized oil is heated to the temperature (90℃)

suitable for centrifugal separation to remove the phospholipids, FFA and other impurities in the crude oil.

Then the oil goes to the washing process.

Bleaching

In normal situation , there is pigment in the crude oil , we need to using the active clay to absorb the

pigment away , after 20 mins , we use the vibrating filter to filter the waste clay away . If you want

to get light color oil , you need to add more active clay . That is mean , the customer can accord to his

requirement to control the oil color. This process is carried out under the vacuum condition.

Deodorization

Usually ,there are some odors in the crude oil , it affects the quality of the edible oil . About our

refining process , we usually use the direct steam to take odors away in the vacuum condition .

General speaking there is about 0.5% water in the alkali refined oil, in the deodorization pot,

thetemperature is very high , it also can finish the dehydration section.

Filtering

This process can remove off the small amount of unsettle gum soluble impurities in the degummed

oil, after oil dehydrate cooling (60 °C), filtering again, to ensure the product oil quality. Then pumping

the final oil into the oil tank.

Automatic control

3, plant cpo refinery processing functions of main parts

(1) Refining section: used to P-acid de-gumming, alkali refining de-acid and water rinsing.

(2) Decoloring section: used to remove off pigments, bleaching oils and grease dehydrate.

(3) Deodorizing section: to remove off the odor components in oil.

(4) Dewax: used to remove off the wax in the oil, in order to get the high quality oil.

(5) Heat-transfer oil stove: supply each device production needing heat energy, temperature reach

above 280C.

(6) Steam generator: produce the needing steam for de-odoring and distillation.

(7) Vacuum pump: supply needing vacuum for dehydrate, de-color, de-odor. Vacuum degree

can reach above 755mm Hg.

(8) Press filter: filter clay, filter out clear oil.

(9) Air compressor: blow dry bleached clay, blow empty the leftover oil in the press filter.

Company Information

Our Strength

1, Established in 1982, we have more than 30 years experience. Our goal is to be pioneer in LDobal grain and oil

industry.

2, We have deep cooperation with Shandong Machine Design Research Institute and Shandong University of

Technology. Our professor often go abroad attending grain and oil conference and forum.

3, We have completed service line including technical department, engineering department, project department,

electronic commerce department, domestic trade department and foreign trade department. After signing

contract, we will set up special team including engineers, installation technicians, drawing designer,

business person, after-sales service person, and so on. We will provide one-to-one service.

Our Service

• Whole set of equipment for production line.

• Motor and power control system.

• Installation material.

• Installation and test-run.

• Drawing of process description, equipment layout, foundation and

  hole, construction.

• Drawing of power control.

• Isolation and painting for equipment.

• Water recycling and cooling system outside the plant (i.e. supplementary device).

• Staff training and long-term technical service.

Main Business Field

• 10-500T/H oil material primary cleaning,drying and storage section turn-key project.
• 100-3000 T/D oil pretreatment, shelling and pre-press workshop turnkey project (soybean hot dehulling, bean skin crushing, the soybean extrusion, high oil contained pre-pressed cake extrusion and high oil contained flakes puffed directly). Rice bran turn-key project.
• 100-3000 T/D leaching workshop turnkey project (towline extractor, rotocel extractor, loop type extractor,
• DTDC separated machine, the full negative pressure evaporation,
• Paraffin wax recovery, leaching workshop degumming, phospholipid concentration).
• 30-1000T/D continuous physical (chemical) refining line.
• 20-3000T/D sunflower oil, rice bran oil, corn germ oil dewaxing turnkey project.
• 10-200T/D fatty acid esterification edible oil production line.

Our Certificates